Ferdowsi Civil Engineering

Ferdowsi Civil Engineering

Experimental study of mechanical properties of high- performance concrete containing steel fibers and polypropylene separately and simultaneously

Document Type : Original Article

Authors
Hamid Naraki 1
Seyed Fathollah Sajedi 1
Masoud Paknahad 2
1 Department of Civil Engineering, Ahvaz Branch, Islamic Azad University, Ahvaz, Iran.
2 Faculty of Engineering, Mahallat Institute of Higher Education, Mahallat, Iran.
10.22067/jfcei.2025.82494.1231
Abstract
This article has studied the separate and simultaneous effect of steel fibers with different shapes and polypropylene (PP) fibers on some mechanical properties of high- performance concrete (HPC). To improve the quality of the cement structure, silica-based aggregates with a maximum size of 9 mm were used instead of natural aggregates. In order to reinforce and investigate the effect of the type, shape and amount of steel fibers on the mechanical properties of HPC, steel fibers in smooth and wavy forms of 30 mm length in 1%, 2%, 3% and 4% were added to the concrete in separate plans. Beside the mentioned steel fibers, PP fibers were added by 1% and the corresponding changes in the mechanical properties were studied. A total of 34 mixing designs were made in the form of 306 cubic, cylindrical and prismatic speceimens, and the compressive, tensile, and bending strengths of each design were investigated at the age of 28 days. The results showed that adding 1% of PP fibers to concrete containing smooth and corrugated steel fibers by (7-8)% leads to the growth of compressive strength up to 113.1 MPa. By adding 1% of PP fibers to concrete containing 3% of corrugated steel fibers, the highest tensile strength of 13.7 MPa was obtained. It was also concluded that changing the shape of fibers from straight to wavy does not show a noticeable effect on compressive strength, while this change showed an average increase of 22% in tensile strength and 34% in bending strength.
Keywords
High performance concrete (HPC)
Mechanical properties
Steel fibers
Polypropylene fibers (PP)
Microsilica (SF)
[1] E. F. O’Neil, B. D. Neeley, and J. D. Cargile, “Tensile properties of very-high-strength concrete for penetration-resistant structures,” Shock and Vibration, vol. 6, no. 5–6, pp. 237–245, 1999. https://doi.org/10.1155/1999/415360
[2] B. A. Tayeh, B. A. Bakar, M. M. Johari, and Y. L. Voo, “Mechanical and permeability properties of the interface between normal concrete substrate and ultra-high performance fiber concrete overlay,” Construction and Building Materials, vol. 36, pp. 538–548, 2012. https://doi.org/10.1016/j.conbuildmat.2012.06.013
[3] L. Mao and S. J. Barnett, “Investigation of toughness of ultra high performance fibre reinforced concrete (UHPFRC) beam under impact loading,” International Journal of Impact Engineering, vol. 99, pp. 26–38, 2017. https://doi.org/10.1016/j.ijimpeng.2016.09.014
[4] C. Wen, P. Zhang, J. Wang, and S. Hu, “Influence of fibers on the mechanical properties and durability of ultra-high-performance concrete: A review,” Journal of Building Engineering, vol. 52, p. 104370, 2022. https://doi.org/10.1016/j.jobe.2022.104370
[5] M. Amin, A. M. Zeyad, B. A. Tayeh, and I. S. Agwa, “Effect of ferrosilicon and silica fume on mechanical, durability, and microstructure characteristics of ultra-high performance concrete,” Construction and Building Materials, vol. 320, p. 126233, 2022. https://doi.org/10.1016/j.conbuildmat.2021.126233
[6] A. E. Naaman and K. Wille, “The path to ultra-high performance fiber reinforced concrete (UHP-FRC): five decades of progress,” in Proceedings of Hipermat, pp. 3–15, 2012.
[7] A. M. Matos, S. C. Figueiredo, S. Nunes, E. Schlangen, and J. L. Barroso-Aguiar, “Durability of an UHPFRC under mechanical and chloride loads,” Construction and Building Materials, vol. 311, p. 125223, 2021. https://doi.org/10.1016/j.conbuildmat.2021.125223
[8] M. G. Sohail, R. Kahraman, N. Al Nuaimi, B. Gencturk, and W. Alnahhal, “Durability characteristics of high and ultra-high performance concretes,” Journal of Building Engineering, vol. 33, p. 101669, 2021. https://doi.org/10.1016/j.jobe.2020.101669
[9] A. M. Tahwia, G. M. Elgendy, and M. Amin, “Durability and microstructure of eco-efficient ultra-high-performance concrete,” Construction and Building Materials, vol. 303, p. 124491, 2021. https://doi.org/10.1016/j.conbuildmat.2021.124491
[10] E. Brühwiler, “Structural UHPFRC: Welcome to the post-concrete era,” International Interactive Symposium on Ultra-High Performance Concrete, vol. 1, no. 1, 2016. https://doi.org/10.21838/uhpc.2016.key
[11] D. Y. Yoo and N. Banthia, “Mechanical and structural behaviors of ultra-high-performance fiber-reinforced concrete subjected to impact and blast,” Construction and Building Materials, vol. 149, pp. 416–431, 2017. https://doi.org/10.1016/j.conbuildmat.2017.05.136
[12] N. Bertola, P. Schiltz, E. Denarié, and E. Brühwiler, “A review of the use of UHPFRC in bridge rehabilitation and new construction in Switzerland,” Frontiers in Built Environment, vol. 155, 2021. https://doi.org/10.3389/fbuil.2021.769686
[13] E. Brühwiler and E. Denarié, “Rehabilitation of concrete structures using ultra-high performance fibre reinforced concrete,” in UHPC-2008: The Second International Symposium on Ultra High Performance Concrete, pp. 05–07, 2008.
[14] H. Wibowo and S. Sritharan, “Use of ultra-high-performance concrete for bridge deck overlays,” IHRB Project TR-683, 2018.
[15] R. Ricciotti, R. Ricciotti, and P. Mazzacane, “The Enrico Navarra Gallery,” Designing and Building with UHPFRC, pp. 79–86, 2011. https://doi.org/10.1002/9781118557839.ch6
[16] V. Perry and G. Weiss, “Innovative field cast UHPC joints for precast bridge decks: Design, prototype testing and projects,” Designing and Building with UHPFRC, pp. 421–436, 2011. https://doi.org/10.1002/9781118557839.ch28
[17] P. Mazzacane, R. Ricciotti, G. Lamoureux, and D. Corvez, “Roofing of the stade Jean Bouin in UHPFRC,” Proceedings of International Symposium on Ultra-High Performance Fibre-Reinforced Concrete, pp. 59–68, 2013.
[18] Y. Huang, S. Grünewald, E. Schlangen, and M. Luković, “Strengthening of concrete structures with ultra-high performance fiber reinforced concrete (UHPFRC): A critical review,” Construction and Building Materials, vol. 336, p. 127398, 2022. https://doi.org/10.1016/j.conbuildmat.2022.127398
[19] M. Schmidt, T. Leutbecher, S. Piotrowski, and U. Wiens, “The German guideline for ultra-high performance concrete,” in Proceedings of the FGC-ACI-fib-RILEM International Symposium on Ultra-High Performance Fibre-Reinforced Concrete, pp. 2–4, 2017.
[20] E. Brühwiler, “Recommendation: Ultra-High Performance Fibre Reinforced Cement-based composites (UHPFRC). Construction material, dimensioning and application,” Lausanne, Switzerland, 2016. https://doi.org/10.1590/S1983-41952017000400011
[21] N. Gowripalan and R. I. Gilbert, “Design guidelines for ductal prestressed concrete beams,” Reference Article, University of New South Wales, 2000.
[22] V. Perry and K. Habel, “Standardization of ultra-high performance concrete: The Canadian perspective,” in Proceedings of International Symposium on Ultra-High Performance Fibre-Reinforced Concrete (UHPFRC), 2017.
[23] J. A. López, P. Serna, and J. Navarro-Gregori, “Advances in the development of the first UHPFRC recommendations in Spain: material classification, design and characterization,” UHPFRC, F. Toutlemonde and J. T. Ch. Resplendino, Eds., pp. 565–574, 2017.
[24] F. JSCE, “Recommendations for design and construction of ultra-high strength fiber reinforced concrete structures (Draft),” Japan Society of Civil Engineers, Tokyo, Japan, 2004.
[25] ASTM C109/C109M-07, “Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens),” ASTM International, West Conshohocken, PA, 2007.
[26] ASTM C496/C496M-17, “Standard Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens,” ASTM International, West Conshohocken, PA, 2017.
[27] ASTM C1609/C1609M-19, “Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading),” ASTM International, West Conshohocken, PA, 2019.
[28] A. Alsalman, C. N. Dang, and W. M. Hale, “Development of ultra-high performance concrete with locally available materials,” Construction and Building Materials, vol. 133, pp. 135–145, 2017. https://doi.org/10.1016/j.conbuildmat.2016.12.040
[29] A. Le Hoang and E. Fehling, “Influence of steel fiber content and aspect ratio on the uniaxial tensile and compressive behavior of ultra-high performance concrete,” Construction and Building Materials, vol. 153, pp. 790–806, 2017. https://doi.org/10.1016/j.conbuildmat.2017.07.130
[30] J. J. Park, D. Y. Yoo, G. J. Park, and S. W. Kim, “Feasibility of reducing the fiber content in ultra-high-performance fiber-reinforced concrete under flexure,” Materials, vol. 10, no. 2, p. 118, 2017. https://doi.org/10.3390/ma10020118
[31] M. Pourbaba, E. Asefi, H. Sadaghian, and A. Mirmiran, “Effect of age on the compressive strength of ultra-high-performance fiber-reinforced concrete,” Construction and Building Materials, vol. 175, pp. 402–410, 2018. https://doi.org/10.1016/j.conbuildmat.2018.04.203
[32] R. Wang and X. Gao, “Relationship between flowability, entrapped air content and strength of UHPC mixtures containing different dosage of steel fiber,” Applied Sciences, vol. 6, no. 8, p. 216, 2016. https://doi.org/10.3390/app6080216
[33] J. Yang, B. Chen, and C. Nuti, “Influence of steel fiber on compressive properties of ultra-high performance fiber-reinforced concrete,” Construction and Building Materials, vol. 302, p. 124104, 2021. https://doi.org/10.1016/j.conbuildmat.2021.124104
[34] J. Esmaeili and A. O. AL-Mwanes, “A review: Properties of eco-friendly ultra-high-performance concrete incorporated with waste glass as a partial replacement for cement,” Materials Today: Proceedings, vol. 42, pp. 1958–1965, 2021. https://doi.org/10.1016/j.matpr.2020.12.242
[35] J. Yu, B. Zhang, W. Chen, and J. He, “Experimental and multi-scale numerical investigation of ultra-high performance fiber reinforced concrete (UHPFRC) with different coarse aggregate content and fiber volume fraction,” Construction and Building Materials, vol. 260, p. 120444, 2020.
[36] D. Y. Yoo, J. H. Lee, and Y. S. Yoon, “Effect of fiber content on mechanical and fracture properties of ultra-high performance fiber reinforced cementitious composites,” Composite Structures, vol. 106, pp. 742–753, 2013. https://doi.org/10.1016/j.compstruct.2013.07.033
[37] Z. Wu, C. Shi, W. He, and D. Wang, “Static and dynamic compressive properties of ultra-high performance concrete (UHPC) with hybrid steel fiber reinforcements,” Cement and Concrete Composites, vol. 79, pp. 148–157, 2017. https://doi.org/10.1016/j.cemconcomp.2017.02.010
[38] A. Alsalman, C. N. Dang, G. S. Prinz, and W. M. Hale, “Evaluation of modulus of elasticity of ultra-high performance concrete,” Construction and Building Materials, vol. 153, pp. 918–928, 2017. https://doi.org/10.1016/j.conbuildmat.2017.07.158
[39] N. Banthia, F. Majdzadeh, J. Wu, and V. Bindiganavile, “Fiber synergy in Hybrid Fiber Reinforced Concrete (HyFRC) in flexure and direct shear,” Cement and Concrete Composites, vol. 48, pp. 91–97, 2014. https://doi.org/10.1016/j.cemconcomp.2013.10.018
[40] P. Rashiddadash, A. A. Ramezanianpour, and M. Mahdikhani, “Experimental investigation on flexural toughness of hybrid fiber reinforced concrete (HFRC) containing metakaolin and pumice,” Construction and Building Materials, vol. 51, pp. 313–320, 2014. https://doi.org/10.1016/j.conbuildmat.2013.10.087
[41] N. A. Libre, M. Shekarchi, M. Mahoutian, and P. Soroushian, “Mechanical properties of hybrid fiber reinforced lightweight aggregate concrete made with natural pumice,” Construction and Building Materials, vol. 25, no. 5, pp. 2458–2464, 2011. https://doi.org/10.1016/j.conbuildmat.2010.11.058
[42] W. Meng and K. H. Khayat, “Effect of hybrid fibers on fresh properties, mechanical properties, and autogenous shrinkage of cost-effective UHPC,” Journal of Materials in Civil Engineering, vol. 30, no. 4, p. 04018030, 2018. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002212
[43] A. Le Hoang and E. Fehling, “Influence of steel fiber content and aspect ratio on the uniaxial tensile and compressive behavior of ultra-high performance concrete,” Construction and Building Materials, vol. 153, pp. 790–806, 2017. https://doi.org/10.1016/j.conbuildmat.2017.07.130
[44] P. S. Song and S. Hwang, “Mechanical properties of high-strength steel fiber-reinforced concrete,” Construction and Building Materials, vol. 18, no. 9, pp. 669–673, 2004. https://doi.org/10.1016/j.conbuildmat.2004.04.027
[45] J. Yang, B. Chen, J. Su, G. Xu, D. Zhang, and J. Zhou, “Effects of fibers on the mechanical properties of UHPC: A review,” Journal of Traffic and Transportation Engineering (English Edition), 2022. https://doi.org/10.1016/j.jtte.2022.05.001
[46] A. Hu, X. Liang, J. Yu, and Q. Shi, “Tensile characteristics of ultra-high-performance concrete,” Magazine of Concrete Research, vol. 70, no. 6, pp. 314–324, 2018. https://doi.org/10.1680/jmacr.17.00126
[47] Y. Li, K. H. Tan, and E. H. Yang, “Influence of aggregate size and inclusion of polypropylene and steel fibers on the hot permeability of ultra-high performance concrete (UHPC) at elevated temperature,” Construction and Building Materials, vol. 169, pp. 629–637, 2018. https://doi.org/10.1016/j.conbuildmat.2018.01.105 
[48] D. Y. Yoo, S. Kim, G. J. Park, J. J. Park, and S. W. Kim, “Effects of fiber shape, aspect ratio, and volume fraction on flexural behavior of ultra-high-performance fiber-reinforced cement composites,” Composite Structures, vol. 174, pp. 375–388, 2017. https://doi.org/10.1016/j.compstruct.2017.04.069
[49] S. Abbas, A. M. Soliman, and M. L. Nehdi, “Exploring mechanical and durability properties of ultra-high performance concrete incorporating various steel fiber lengths and dosages,” Construction and Building Materials, vol. 75, pp. 429–441, 2015. https://doi.org/10.1016/j.conbuildmat.2014.11.017
[50] W. C. Choi, K. Y. Jung, S. J. Jang, and H. D. Yun, “The influence of steel fiber tensile strengths and aspect ratios on the fracture properties of high-strength concrete,” Materials, vol. 12, no. 13, p. 2105, 2019. https://doi.org/10.3390/ma12132105
[51] S. Teng, V. Afroughsabet, and C. P. Ostertag, “Flexural behavior and durability properties of high performance hybrid-fiber-reinforced concrete,” Construction and Building Materials, vol. 182, pp. 504–515, 2018. https://doi.org/10.1016/j.conbuildmat.2018.06.158
[52] Z. Wu, C. Shi, W. He, and L. Wu, “Effects of steel fiber content and shape on mechanical properties of ultra-high performance concrete,” Construction and Building Materials, vol. 103, pp. 8–14, 2016. https://doi.org/10.1016/j.conbuildmat.2015.11.028
Send comment about this article
Enter Name.
Enter a valid email address.
Enter a vaid affiliation.
Enter comments (At leaset 10 words)
CAPTCHA Image
Enter Security Code Correctly.