Experimental Evaluating the Effect of Steel Fibers on the Mechanical Properties of Roller-compacted Concrete

Document Type : Original Article

Authors

• Ramin Chaleshi ¹
• Babak Golchin ²
• Ramin Meshkabadi ³

¹ Department of Civil Engineering, Ahar Branch, Islamic Azad University, Ahar, Iran

² Department of Civil Engineering, University of Mohaghegh Ardabili, Ardabil, Iran

³ Department of Engineering Sciences, Faculty of Advanced Technologies, University of Mohaghegh Ardabili, Namin, Iran

10.22067/jfcei.2024.79344.1186

Abstract

The use of roller-compacted concrete in construction projects, such as road paving, parking lots, dam construction, and industrial pavement, is attributed to its quick implementation, relatively low cost, and sufficient strength without the need for steel bar. However, the brittle nature of roller-compacted concrete prompted an investigation into how steel fibers could improve its mechanical behavior. This research focused on the effect of steel fibers on fracture strength, compressive strength, and tensile strength of roller-compacted concrete. The study involved testing semicircular samples with edge cracks under three-point bending loading to simulate pure tension, pure shear, and their combination. Additionally, the compressive and tensile strength of roller-compacted concrete samples with steel fibers were evaluated at 7 and 28 days. The laboratory results showed that adding 0.1%, 0.3%, and 0.5% steel fibers improved the 28-day compressive strength by 12%, 15%, and 36%, respectively, and the tensile strength by 14%, 21%, and 39%, respectively. Moreover, the failure load of all samples increased in all loading modes with higher percentages of steel fibers, leading to greater resistance to crack growth. The study identified 0.3% of steel fibers as the most effective amount for improving the fracture resistance of roller-compacted concrete in different loading modes, while the optimal percentage for enhancing the compressive and tensile strength was determined to be 0.5%.

Keywords

• Roller-compacted Concrete
• Steel Fibers
• Strength
• Fracture Toughness

---

References

1. "Guidelines for the design, implementation and maintenance of concrete paving of roads", The Plan and Budget Organization, (2018).
2. LaHucik, S. Dahal, J. Roesler and A. N. Amirkhanian, "Mechanical Properties of Roller-compacted Concrete with Macro-fibers", Construction and Building Materials, Vol. 135, pp. 440-446, (2017). https://doi.org/10.1016/j.conbuildmat.2016.12.212
3. Zhang, S. Gong and J. Zhang, "Effect of Rubber Particles and Steel fibers on Frost Resistance of Roller Compacted Concrete in Potassium Acetate Solution", Construction and Building Materials, Vol. 187, Pp. 752-759, (2018). https://doi.org/10.1016/j.conbuildmat.2018.07.244
4. Fuan, M. Ke, L. Kanghe, L. Kun and M. R. M. Aliha, "Influence of Specimen Geometry on Mode I Fracture Toughness of Asphalt Concrete", Construction and Building Materials, Vol. 276, pp. 122181, (2021). https://doi.org/10.1016/j.conbuildmat.2020.122181
5. Vazifehkhah, A. R. Manafpour, "Effects of Steel and Polypropylene Fibers on Tensile Strength of FRC with the Same Base Strength", Journal of Civil and Environmental Engineering, Vol. 42, no. 69, pp. 47-56, (2013).
6. shaddel, M. Kheyry ghojehbigli and A. Enayati Tekleh, "Behavior Pattern of Compressive and Tensile Strength of Structural Lightweight Concrete Consisting perlite, Leca and Steel Fiber", Analysis of Structure and Earthquake, Vol. 15, no. 2, pp. 47-57, (2018).
7. Leone, G. Centonze, D. Colonna, F. Micelli and M. A. Aiello, "Fiber-reinforced Concrete with Low Content of Recycled Steel Fiber: Shear Behaviour", Construction and Building Materials, Vol. 161, pp.141-155, (2018).
8. https://doi.org/10.1016/j.conbuildmat.2017.11.101
9.  Sukontasukkul, U. Chaisakulkiet, P. Jamsawang, S. Horpibulsuk, C. Jaturapitakkul and P. Chindaprasirt, "Case investigation on application of steel fibers in roller compacted concrete pavement in Thailand", Case studies in construction materials, Vol.11, (2019). https://doi.org/10.1016/j.cscm.2019.e00271
10.  Seifollahi, Y. Mohammadi, "The effects of nano silica and steel fibers on mechanical properties of roller-compacted concrete pavement", Concrete Research, Vol. 13, No. 2, Pp. 31-43, (2020).
11. Abu-Bakr, H. F. Mahmood and A. A. Mohammed, "Investigation of metakaolin and steel fiber addition on some mechanical and durability properties of roller compacted concrete", Case Studies in Construction Materials,Vol.16, (2022).https://doi.org/10.1016/j.cscm.2022.e01136
12.  Fakhri, E. Amoosoltani, "The Effect of Reclaimed Asphalt Pavement and Crumb Rubber on Mechanical Properties of Roller Compacted Concrete Pavement", Construction and Building Materials, Vol. 137, Pp. 470-48, (2017). https://doi.org/10.1016/j.conbuildmat.2017.01.136
13. Rahmani, M. K. Sharbatdar, M. H. Beygi, "The effect of water-to-cement ratio on the fracture behaviors and ductility of Roller Compacted Concrete Pavement (RCCP)", Theoretical and Applied Fracture Mechanics, Vol.109, pp. 102753, (2020). https://doi.org/10.1016/j.tafmec.2020.102753
14.  Sengun, B. Alam, R. Shabani and I. O. Yaman, "Strength and fracture properties of roller compacted concrete (RCC) prepared by an in-situ compaction procedure", Construction and Building Materials, Vol.271, Pp.121563, (2021). https://doi.org/10.1016/j.conbuildmat.2020.121563
15.   R. M. Aliha, A. Razmi, A. Mansourian, "The Influence of Natural and Synthetic Fibers on Low Temperature Mixed Mode I+ II Fracture Behavior of Warm Mix Asphalt (WMA) Materials", Engineering Fracture Mechanics, Vol. 182, Pp. 322-336, (2017).https://doi.org/10.1016/j.engfracmech.2017.06.003
16.   Golchin, R. Safayi, "Effect of Carbon Fibers on Fracture Toughness of Asphalt Mixtures Using Linear Elastic Fracture Mechanics", Journal of Transportation Infrastructure Engineering, Vol. 4, no 2, pp. 77-92, (2018), (In Persian).
17.   M. Mirsayar, A. Razmi, M. R. M. Aliha and F. Berto, "EMTSN Criterion for Evaluating Mixed Mode I/II Crack Propagation in Rock Materials", Engineering Fracture Mechanics, Vol. 190, pp. 186-19, (2018).https://doi.org/10.1016/j.engfracmech.2017.12.014
18.  Delnavaz, K. Eshaghi, "Treatment of Petroleum Wastewater Using new Fe-ZSM-5@TiO2/Ag Nano Photocatalys", Ferdowsi Civil Engineering, Vol. 34, No. 2, pp. 71-86, (2021), (In Persian).
19. Golchin, M. Aliyan and R. Meshkabadi, "Evaluating the Effect of Para-fiber on the Technical Properties of in Plant Hot Recycled Asphalt Mixture and Determining a Suitable Combination", Journal of Transportation Research, Vol. 20, No. 3, pp. 85-102, (2023), (In Persian). 
20. R. Kordjazi, F. Pooya Nejad and F. Shahabian, "Modeling the Patch Load Resistance of Plate Girders Using a Support Vector Machine", Ferdowsi Civil Engineering, Vol. 28, No. 2, Pp. 109-124, (2016), (In Persian).
21.   Kordjazi, f. Pooya Nejad, "Prediction of Ultimate Bearing Capacity of Axially Loaded Piles Using a Support Vector Machine", Ferdowsi Civil Engineering, Vol. 24, No. 1, pp. 71-90 (2012), (In Persian).