1. Asghari, A., "Dynamics of Structures, Basic and Applications to Earthquake Engineering", Volume 1,2, Publisher: Amirkabir University of Technology, Tehran, Iran, (2013).
2. BHRC, "Iranian Code of Practice for seismic Resistant Design of Buildings: Standard No. 2800 (4rd Edition) ", Building and Housing Research Center, (2015).
3. Uriz, P., Filippou, F.C. and Mahin, S.A., "Model for cyclic inelastic buckling of steel braces", J. Struct. Eng., No 134(4), pp. 619–628, (2008).
4. Uriz, P. and Mahin, S.A., "Toward earthquake-resistant design of concentrically braced steel-frame structures", PEER-2008/08, Pacific Earthquake Engineering Research Center (PEER), Univ. of California, Berkeley, Berkeley, CA; (2008).
5. Uang, C.M. and Nakashima, M., "Steel buckling-restrained frames", 16, Earthquake engineering: From engineering seismology to performance-based engineering, Y. Bozorgnia and V. V. Bertero, eds, CRC Press, Boca Raton, FL; (2004).
6. Mofid, M., Lotfollahi, M., "On the characteristics of new ductile knee bracing systems", Journal of Constructional Steel Research, No 62, pp.271–281, (2006).
7. Balendra, T., Huang, X., "Overstrength and ductility factors for steel frames designed according to BS 5950", Journal of Structural Engineering, ASCE 2003; No 129(8), pp. 1019–35, (2003).
8. Kim, J., Choi, H., "Response modification factors of chevron-braced frames", Engineering Structures, No. 27,pp. 285–300, (2005).
9. Maheri, MR., Akbari R., "Seismic behavior factor, R, for steel X-braced and knee-braced RC buildings", Engineering Structures, No. 25(15), pp.1505–13, (2003).
10. Mahmoudi, M., Zaree, M., "Evaluating response modification factors of concentrically braced steel frames", Journal of Constructional Steel Research; No. 66, pp. 1196-1204, (2010).
11. Asgarian, B., Shokrgozar, HR., "BRBF response modification factor", Journal of Constructional Steel Research;No. 65(2), pp. 290-8, (2009).
12. MHUD, "Iranian National Building Code, Part 10, Steel Structure Design", Tehran (Iran): Ministry of Housing and Urban Development; (2013).
13. American Institute of steel construction (AISC341), "Seismic Provisions for Structural Steel Buildings", (2010).
14. American Society of Civil Engineers (ASCE7), "Minimum Design Loads for Buildings and Other Structures", pp.7, (2010).
15. ETABS, "Integrated building design software", version 9.7.3, Berkeley; (California), USA: Inc., (1995).
16. American Institute of steel construction, "Specification for structural steel buildings", (2010).
17. Federal Emergency Management Agency (FEMA), "Prestandard and Commentary for the Seismic Rehabilitation of Buildings", (FEMA 356), Washington, DC, (2000).
18. Balendra, T. and Huang, X., "Overstrength and Ductility Factors for Steel Frames Designed According to BS 5950", Journal of Structural Engineering, ASCE, Vol. 129, No. 8, (2003).
19 .Newmark, N.M. and Hall, W.J., "Seismic Design Criteria for Nuclear Reactor Facilities", Rep. No. 46, Building Practices for Disaster Mitigation, National Bureau of Standards, U.S. Department of Commerce, (1973).
20. Newmark, N.M. and Hall, W.J., "EERI Monograph Series", Earthquake Spectra and Design, Earthquake Engineering Research Institute, Oakland, California, (1982).
21. Lai, S.P. and Biggs, J.M., "Inelastic Response Spectra for Seismic Building Design", Journal of Structural Engineering, ASCE, Vol. 106, No. ST6, (1980).
22. Miranda, E., "Site-Dependent Strength Reduction Factors", Journal of Structural Engineering, ASCE, Vol. 119, No. 12, (1993).
23.Miranda, E. and Bertero, V.V., "Evaluation of Strength Reduction Factors for Earthquake-Resistant Design", Earthquake Spectra, Vol. 10, No. 2, (1994).
ارسال نظر در مورد این مقاله