@article { author = {bahrami yarahmadi, mohammad and Shafai Bejestan, mahmood}, title = {Study of the Effect of Effective Length Variations of Triangular-Shaped Vanes on Erosion and Sedimentation Pattern in a 90° Mild Bend}, journal = {Ferdowsi Civil Engineering}, volume = {27}, number = {1}, pages = {87-100}, year = {2016}, publisher = {Ferdowsi University of Mashhad Press}, issn = {2783-2805}, eissn = {2783-199X}, doi = {10.22067/civil.v27i1.24565}, abstract = {Application of structures of flow pattern modification is one of the erosion control methods in bends. Triangular vanes are among these structures which provide less scour depth compared to the other techniques such as spur dike. Since little information on erosion and sedimentation pattern around triangular vanes are available, this study was conducted to study the effect of structure effective length variations on erosion and sedimentation pattern. Therefore a triangular vane with different effective lengths (23.3, 17.5, 14 and 10 cm) was tested under different hydraulic conditions (Froude numbers 0.194, 0.214, 0.233 and 0.253). For all experiments, single triangular vane was installed with an angle of 30° relative to the upper bank and outside bend of flume in the 72° location which maximum scour depth is usually occurs. For all tests, flow depth was kept constant equal to 13 cm. At the end of each test bed topography was measured and from that the geometry of scour hole and point bar was measured. The results showed that maximum scour depth has been reduced by reducing of vane effective length. Variations of scour depth for low Froude numbers (0.194 and 0.214) was found to be more than high Froude numbers (0.233 and 0.253). Eroded sediments were transported downstream of vane and accumulated closed to the outer bank. The results showed that, in effective length 10 cm point bar distance from the beginning of vane was almost 0.8 times the effective length of vane for Froude number 0.233 and in effective lengths 14 and 10 cm was respectively, 1 and 2 times the effective length of vane for Froude number 0.253. In addition, minimum point bar distance from the outer bank has been reduced by reducing of vane effective length. For effective lengths of 14 and 10cm the point bar distance from the outer bank was almost 1.5-2 percent width of the flume.}, keywords = {triangular-shaped vane,vane effective length,90° mild bend,scour and sedimentation}, title_fa = {بررسی تغییرات طول موثر صفحات مثلثی شکل بر الگوی فرسایش و رسوبگذاری در قوس ملایم 90 درجه}, abstract_fa = {چکیده- استفاده از سازه های اصلاح الگوی جریان در قوس ها از جمله روش های کنترل فرسایش در قوس ها محسوب می شود. صفحات مثلثی (سرریزهای مثلثی) از جمله این سازه ها می باشند که نسبت به دیگر سازه های اصلاح کننده الگوی جریان مانند آبشکن، عمق آبشستگی کمتری ایجاد می‌کنند. با توجه به اینکه اطلاعات اندکی در رابطه با الگوی فرسایش و رسوبگذاری اطراف صفحات مثلثی شکل وجود دارد بنابراین در این تحقیق به بررسی تغییرات طول موثر سازه بر الگوی فرسایش و رسوبگذاری در قوس ملایم 90 درجه پرداخته شده است. لذا در این تحقیق صفحه‌ی مثلثی شکل به ازای طول های موثر مختلف (3/23، 5/17، 14 و 10 سانتیمتر) و تحت شرایط هیدرولیکی متفاوت (اعداد فرود 194/0، 214/0، 233/0 و 253/0) مورد آزمایش قرار گرفت. در همه آزمایشات تک صفحه مثلثی شکل با زاویه 30 درجه نسبت به ساحل بالادست و در موقعیت بیشترین عمق آبشستگی قوس 90 درجه ملایم یعنی زاویه 72 درجه نصب گردید. عمق جریان در تمام آزمایش‌ها ثابت و برابر 13 سانتیمتر بوده است. در انتهای هر آزمایش توپوگرافی بستر برداشت گردید و با توجه به آن هندسه چاله فرسایشی و پشته رسوبگذاری تعیین گردید. نتایج این تحقیق نشان دادند که با کاهش طول موثر حداکثر عمق آبشستگی کاهش می یابد. در اعداد فرود 194/0 و 214/0 روند تغییرات بیش از اعداد فرود 233/0 و 253/0 بوده بگونه ای که در اعداد فرود بالا اثر طول موثر بر حداکثر عمق آبشستگی اندک می باشد. رسوبات فرسایش یافته در راستای محور سازه توسط جریان نزدیک بستر به طرف ساحل بیرونی منتقل می شوند. نتایج نشان داد که در عدد فرود 233/0 فاصله شروع رسوبگذاری از ابتدای سازه در طول موثر یک هفتم عرض مجرا حدود 8/0 برابر طول موثر و در عدد فرود 253/0 در طول های موثر یک پنجم و یک هفتم عرض مجرا بترتیب حدود 1 و 2 برابر طول موثر سازه می باشد. از دیگر نتایج این تحقیق این بود که با کاهش طول موثر سازه حداقل فاصله پشته رسوبگذاری از ساحل بیرونی کاهش می یافت. فاصله پشته رسوبی از ساحل بیرونی در طول های موثر یک پنجم و یک هفتم عرض مجرا اختلاف اندکی با هم دارند و حدود 2-5/1 درصد عرض فلوم می باشند.}, keywords_fa = {صفحه مثلثی شکل,طول موثر صفحه,قوس ملایم 90 درجه,فرسایش و رسوبگذاری}, url = {https://civil-ferdowsi.um.ac.ir/article_28999.html}, eprint = {https://civil-ferdowsi.um.ac.ir/article_28999_965a88cd3cb4ae9dff7522c35f5d88c5.pdf} }